Yamaha DXR15 Instrukcja obsługi

Marka: Yamaha

Model: DXR15

Kategoria: Wzmacniacz instrumentów muzycznych

Typ: Instrukcja obsługi

OWNER’S MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

MANUALE DI ISTRUZIONI

EnglishDeutschFrançaisEspañolItaliano

2 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsu-

lated “dangerous voltage” within the prod-

uct’s enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the litera-

ture accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

specified by the

manufacturer, or sold with the

apparatus. When a cart is

used, use caution when

moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifi-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this product

in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regu-

lations does not guarantee that interference will not occur in

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

all installations. If this product is found to be the source of

interference, which can be determined by turning the unit

“OFF” and “ON”, please try to eliminate the problem by

using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT.

The wires in this mains lead are coloured in accordance with the fol-

lowing code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

(3 wires)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,

AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

* This information is located on the bottom of the unit.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B

EST CONFORME À LA NORME NMB-003 DU CANADA.

4 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

English

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Only use the voltage specified as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place on it any containers (such as vases, bottles or glasses) containing

liquids which might spill into any openings. If any liquid such as water seeps

into the device, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualified Yamaha service

personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power

switch and disconnect the electric plug from the outlet. Then have the device

inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the device.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Unless the device is securely affixed, do not install it in a location where it might

fall, even if the surface is level.

• Do not block the vents. This device has ventilation holes at the rear to prevent

the internal temperature from becoming too high. Inadequate ventilation can

result in overheating, possibly causing damage to the device(s), or even fire.

• Do not use the device in a confined, poorly-ventilated location. Make sure that

there is adequate space between the device and surrounding walls or other

devices: at least 30cm at the sides, 30cm behind and 30cm above. Inadequate

ventilation can result in overheating, possibly causing damage to the device(s),

or even fire.

• Do not use the speaker’s handles for suspended installation. Doing so can result

in damage or injury.

• Do not hold the bottom of the device when transporting or moving it. In doing

so, you may pinch your hands under the device, and result in injury.

• Do not press the rear panel of the device against the wall. Doing so may cause

the plug to come in contact with the wall and detach from the power cord,

resulting in short circuiting, malfunction, or even fire.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Before moving the device, remove all connected cables.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Location

PA_en_1 1/2

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 5

English

• When setting up the device, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• When transporting or moving the DXS15, DXS12, or DXR15, always use two or

more people. Attempting to lift the DXS15, DXS12, or DXR15, by yourself may

damage your back, result in other injury, or cause damage to the device itself.

• If you use the pole socket on the DXS15 to mount a satellite speaker, use a

speaker of 19.3kg (42.5lbs) or less in weight and 60.1cm (23-5/8") or less in

height. If you use the pole socket on the DXS12 to mount a satellite speaker, use

a speaker of 14.6kg (32.2lbs) or less in weight and 50.2cm (19-6/8") or less in

height. Also, use a speaker pole no longer than 120cm (47.2") with an outer

diameter of 35mm (1-3/8").

• Always consult qualified Yamaha service personnel if the device installation

requires construction work, and make sure to observe the following precautions.

- Choose mounting hardware and an installation location that can support the

weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your fingers or hands in any gaps or openings on the device

(panel).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (panel) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• Do not use the device for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not operate the device if the sound is distorting. Prolonged use in this

condition could cause overheating and result in fire.

• Do not pull the cables connected to the microphones, etc.

Interference From Cell Phones

Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service

personnel about replacing defective components.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.

• Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Connections

Maintenance

Handling caution

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

PA_en_1 2/2

6 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

Introduction

English

Introduction

Thank you for purchasing the Yamaha DXR series powered speaker or DXS series powered subwoofer.

Please read this manual thoroughly to ensure optimum use of the DXR/DXS series for the longest possible period of time.

Keep the manual in a safe place for future reference.

Contents

Introduction............................................................................. 6

Main Features of the DXR/DXS Series.................................. 6

Controls and Functions .......................................................... 7

Setup Examples ................................................................... 10

Troubleshooting.................................................................... 12

References ........................................................................... 80

Main Features of the DXR/DXS Series

■ FIR-X tuning™(DXR series)

The advanced DSP processing featured in these series has

been inherited from the high-end DSR series. Our proprietary

sound-processing technology utilizing a linear-phase FIR

filter delivers excellent sound quality at high resolution with a

smooth frequency response that is unaffected by phase

interference near the crossover point.

■ D-CONTOUR (Dynamic CONTOUR)

(DXR series)

D-CONTOUR is a multiband compressor that dynamically

controls the level of each frequency range according to the

application and human hearing characteristics. It features a

FOH/MAIN mode for using your DXR as a main speaker, and

a MONITOR mode that has been optimized for use as a floor

monitor. Select the mode that suits your application.

■ D-XSUB (DXS series)

D-XSUB is a newly-developed processing technology

exclusively for subwoofers that dynamically controls the low

frequency range. It features a BOOST mode that enhances

and provides punch to the sound, and an XTENDED LF mode

that extends the bottom of the low frequency range. You can

select either mode in accordance with various applications

and musical genres.

■ Mixing/LINK functionality (DXR series)

The DXR series features mixing functionality, enabling you to

mix sounds by directly inputting three channel signals into

the unit.

In addition, the LINK function enables you to easily configure

a stereo or dual-mono SR (Sound Reinforcement) system

using two DXRs.

■ DSP-controlled advanced protection

system

Powerful protection circuits ensure secure protection in the

speaker unit, amplifier unit, and power supply unit. This

protection functionality promotes optimal performance of

each component and optimum reliability without distortion

even in challenging environments.

Included Accessories

•AC power cord

•Owner’s manual (this book)

Optional accessories

U brackets for mounting the DXR series on the wall or ceiling

are available as follows:

•UB-DXR15 (for DXR15)

•UB-DXR12 (for DXR12)

•UB-DXR10 (for DXR10)

•UB-DXR8 (for DXR8)

DXR8 DXR10 DXR12 DXS12DXR15 DXS15

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 7

Controls and Functions

English

Controls and Functions

Rear panel

INPUT jacks

These are balanced XLR input jack(s) (INPUT 1), unbalanced

phones (INPUT 2) and RCA pin input jacks (INPUT 3).

You can connect a mixing console or microphone to INPUT

1, a keyboard or electric-acoustic guitar to INPUT 2, and a

portable audio player or CD player to INPUT 3. Signals from

INPUT 1-3 are mixed inside the DXR unit.

The DXS series input features only balanced XLR input jacks

(L, R). L and R signals are mixed inside the DXS unit.

THRU jack(s)

These are balanced XLR output jack(s). Input signals will be

passed through unaffected, since these are parallel

connected to the INPUT jacks.

LEVEL control

Adjusts the level of each INPUT signal. If you connect a

device that features a nominal output level of +4dBu (such as

a mixing console), set the MIC/LINE switch () on the DXR

series to LINE, and adjust the LEVEL control using its 12

o’clock position as a reference.

LIMIT indicator

Lights when the output limiter is active. The output limiter will

operate in order to protect the speaker and amp, attenuating

the output signal to the amplifier. If this indicator stays lit,

lower the level of the input signal.

NOTE

• If the output voltage of the amplifier has exceeded the maximum

value, or if excessive integral power consumption is detected, the

LIMIT indicator will light when the amount of attenuation is 3dB or

higher.

• The integral power consumption refers to the sum of power

consumption provided to the speaker driver per unit time.

SIGNAL indicator

Lights when an audio input signal is detected.

PROTECTION indicator

Lights when the protection system is active. The protection

system will operate and the speaker output will be muted in

the following situations.

• If amplifier overheating is detected:

• If DC output is detected:

• If overcurrent is detected:

•

When turning the power on:

The protection system will be activated to prevent noise and

the indicator will light for about two seconds. The indicator

turns off when the power supply has started normally.

•

When turning the power off:

Or if the power turns off due to an unexpected error, the

protection system will be activated to prevent noise, and then

the power will be shut down.

NOTE

If the protection system has engaged after the problem was

detected, waiting until the amplifier cools down or powering off and

on again will return to normal operation. If the unit does not return to

normal operation, please contact your Yamaha dealer.

DXR15, DXR12, DXR10, DXR8 DXS15, DXS12

8 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

Controls and Functions

English

POWER indicator

Lights when the power switch ( ) is set to on.

FRONT LED DISABLE switch

Selects turning on or off the FRONT LED at the left of the

unit’s front grille. The LED will light when this switch is set to

off () . Turn this switch on ( ) when you want to turn off the

LED.

NOTE

When the limiter for protecting the amplifier operates, the LED will

light brighter than usual in proportion to the amount of attenuation

(3dB or higher).

MIC/LINE switch (DXR series)

Set this switch to MIC or LINE for INPUT1 jack, depending on

the level of the input signal. For low-level signals (such as

microphones), set the switch to the MIC position. For high

level signals (such as mixer), set the switch to the LINE

position.

D-CONTOUR switch (DXR series)

Selects one of the D-CONTOUR (Dynamic CONTOUR)

presets. The FOH/MAIN setting will boost the high and low

frequency components so that the frequency response will

become suitable for a main speaker. The MONITOR setting

also suppresses the low range, which could otherwise tend

to be boomy if the speaker is set directly on the floor or used

along with a main speaker. With the FOH/MAIN or MONITOR

setting, the D-CONTOUR function is enabled and controls

the boost and attenuation amounts dynamically in relation to

the sound volume. When this switch is set to OFF, a generic

frequency response setting will be used and the

D-CONTOUR function will be turned off.

HPF switch (DXR series)

Specifies the HPF’s cut-off frequency.

If the switch is set to 120Hz or 100Hz, the high-pass filter will

cut the frequency components below that threshold. If you

plan to use your DXR without a subwoofer, set this switch to

OFF. If you plan to use the DXR along with a subwoofer, we

recommend that you set this switch to 120Hz or 100Hz.

LINK OUT jack (DXR series)

This XLR jack outputs signals (routed from each INPUT jack)

to a connected DXR series speaker. Connect this jack to the

INPUT 1 (XLR) jack on the linked DXR series speaker.

Signals at the LINK OUT jack are line-level. Set the MIC/LINE

switch on the linked DXR series speaker to LINE. For stereo

signals, set the LEVEL control on the linked DXR to the 12

o’clock position to balance the levels between two DXRs.

LINK MODE switch (DXR series)

Enables you to select whether the mixed signal (on the

original DXR) will be played in stereo or monaural on the

original and linked DXRs. The following signals are mixed

and output according to the switch setting.

NOTE

If you use only a single, stand-alone DXR, set this switch to MONO

( ). If you set the switch to STEREO ( ), audio signals input at the

R channel of INPUT 2/3 will not be output.

POLARITY switch (DXS series)

Selects the subwoofer polarity.

In most cases, for example if the subwoofer and DXR series

speaker are installed on a speaker pole, set this switch to

NORM (NORMAL). However, an INVT (INVERTED) setting

may improve low-range response, depending on the type

and location of the speaker system. Try both settings and

select the one that produces the best low-end sound.

D-XSUB switch (DXS series)

Selects one of the D-XSUB presets. The BOOST setting

boosts the low frequency range to enhance and punch-up

the frequency response. The XTENDED LF extends the

bottom of the low frequency range to enhance broad low-

range frequency response. With the BOOST or XTENDED LF

setting, the D-XSUB function is enabled and controls the

boost amount dynamically in relation to the sound volume.

When this is set to OFF, a generic frequency response will be

used and the D-XSUB function will be turned off.

LPF switch (DXS series)

Specifies the low-pass filter’s cutoff frequency at 120Hz,

100Hz, or 80Hz. The filter will cut the frequency components

above the specified threshold. If you are using the DXS along

with a DXR, match this frequency to DXR’s HPF switch

setting.

LINK MODE STEREO MONO

Input of the

original DXR

INPUT1

INPUT2/3

INPUT1

INPUT2/3

LR LR

Output of the

original DXR



–



Output of the

linked DXR



–



DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 9

Controls and Functions

English

AC IN socket

Connect the supplied AC power cord here. First, connect the

power cord to the device, then insert the power cord plug

into the AC outlet.

Be sure to turn the power off before connecting

or disconnecting the power cord.

Power switch

Turns the power supply on or off.

Press the switch to the On position to turn the power on ( ).

NOTE

If you are using multiple devices, turn on the power to each device

individually. If you turn on the power to multiple devices

simultaneously, a temporary drop in the power voltage may occur,

possibly resulting in abnormal operation of the devices.

Rapidly turning the unit on and off in

succession can cause it to malfunction. After

turning the unit off, wait for about 5 seconds

before turning it on again.

Tiltable pole socket (DXR series)

This mount has two pole sockets. You can choose the angle

of the DXR (mounted on a speaker pole) so that the speaker

will be horizontal to the floor or tilting toward the floor by 7

degrees.

Suspended installation

If you plan to suspend your DXR series speaker, attach

commercially-available eye bolts to the screw holes (which

are sealed at the time of shipment) located on the top (two

locations) and on the lower part of the rear (one location).

The size of the screw holes on the DXR15 and DXR12 is

M10 (for an eye bolt length of 18mm or less). The size of

the screw holes on the DXR10 and DXR8 is M8 (for an eye

bolt length of 15mm or less). Keep in mind that you will

need three eye bolts to suspend it. Make sure to use the

eye bolts according to the standards and safety

regulations in your area.

Before doing any installation or construction

work, consult with an installation expert.

When choosing the installation location,

suspension wire and mounting hardware, make

sure all are strong enough to support the

weight of the speaker.

Some fittings may deteriorate over extended

periods of time due to wear and/or corrosion.

For optimum safety, the installation should be

checked thoroughly at regular intervals.

Yamaha cannot be held responsible for damage

or injury caused by insufficient strength of the

support structure or improper installation.

DXR15, DXR12, DXR10, DXR8, DXS15, DXS12

CAUTION

7˚

0˚

7˚

CAUTION

10 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

Setup Examples

English

Setup Examples

1. Basic SR system

This example illustrates a basic SR system setup using two 2-way speakers. The system is suitable for a small-sized live

space, a restaurant and a practice studio. As necessary, add a stage monitor system illustrated in no. 3.

2. SR system with subwoofer

This example illustrates an SR system setup using two 2-way speakers and subwoofers with speaker poles. The system is

suitable for a small-sized music venue, a

house of worship and an event site. We recommend that the subwoofer’s input

LEVEL control is set to a 12 o'clock position. If you prefer, you can adjust the level as desired. As necessary, add a stage

monitor system illustrated in no. 3.

NOTE

Pole sockets for mounting speaker poles are provided at the bottom of the DXR series, and at the top of the DXS series. Please refer to the

“Precautions” (page 4).

If you use multiple subwoofers at the same time, set the POLARITY switch of adjacent subwoofers to the same position. Otherwise, the sounds

from each speaker may cancel each other, resulting in diminished sound pressure.

Yamaha recommends that if you use the DSR118W as a subwoofer in combination with the DXR15 or DXR12. In this case, set HPF to 120Hz.

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 11

Setup Examples

English

3. Stage monitor system

This SR system is suitable as a performer’s monitoring system. For use as a vocal monitor, set D-CONTOUR to MONITOR.

As necessary, connect speakers in parallel.

NOTE

Up to four speakers can be connected in parallel.

4. SR system with a single DXR

This example illustrates an SR system using one 2-way speaker connected directly to a microphone, musical instrument, or

playback source. This system can be used in a wide range of places such as corporate events, presentations, and

restaurants. Adjust the volume with the LEVEL control to prevent feedback.

5. Simple SR system with two DXRs

This example illustrates a simple SR system using two 2-way speakers linked to each other. This system is suitable for a small-

sized live venue. Audio can be output in stereo or monaural, by using one 2-way speaker connected directly to a microphone,

musical instrument, or BGM sound source, then linking the speaker to another 2-way speaker via the LINK OUT jack. If you

want to output in stereo, set the LINK MODE switch to the stereo position.

MONO

STEREO

12 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

Troubleshooting

*If any specific problem should persist, however, please contact your Yamaha dealer.

Symptom Possible causes Possible solution

Power does not turn on.

The power cord is not connected

properly.

Connect the power cord properly.

Power suddenly went

off.

The protection system has

operated, shutting down the power

supply.

Turn off the power, wait until the amplifier cools

down, and then turn on again.

No sound.

The cable is not connected

properly.

Connect to the INPUT jack properly.

The LINK MODE switch is set

incorrectly.

If you are using a single DXR, set the LINK

MODE switch to MONO.

Sound is interrupted

suddenly.

The protection system has

operated, muting the output.

Wait until the amplifier cools down. If the device

won’t automatically reset itself, turn off the power,

and then on again.

Sound howls

(feedback)

A microphone is directed toward the

speaker.

Keep the speaker away from the area where the

microphone picks up sound.

Sound is amplified too much.

Lower the volume of the input device and locate

the microphone more closely to the sound

source.

The setting of the HPF switch is not

appropriate.

Set the HPF switch on 120Hz or 100Hz if you get

feedback in low frequency bands.

Each speaker sound

differs

(if multiple speakers

are used)

Settings for each speaker differ.

• (DXR series) Set the HPF and D-CONTOUR

switches of each speaker to the same

positions.

• (DXS series) Set the POLARITY switch, the LPF

switch, and D-XSUB switch of each speaker to

the same position.

Sound is distorted

Input volume is excessive.

• Lower the volume of the input device to a point

no higher than where the LIMIT indicator lights

occasionally.

• If sound continues to be distorted even if you

turn down the volume to the minimum, set the

MIC/LINE switch to the LINE position (if the

switch is set to MIC).

Output volume is excessive.

Use the LEVEL control to lower the output level to

a point no higher than where the LIMIT indicator

lights occasionally.

The microphone

volume is too low.

The MIC/LINE switch is set to LINE. Set the MIC/LINE switch to the MIC position.

Low and high

frequency are

unbalanced.

The output limiter is active.

Lower the input level or the output level to a point

no higher than where the LIMIT indicator lights

occasionally.

80 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

References

Italiano

Español

Français

Deutsch

English

References

Specifications

General DXR15 DXR12 DXR10 DXR8 DXS15 DXS12

System Type 2-way, Bi-amp Powered Speaker, Bass-reflex Type Powered Subwoofer, Band-pass Type

Frequency Range (-10dB) 49Hz – 20kHz 52Hz – 20kHz 56Hz – 20kHz 57Hz – 20kHz 45Hz – 160Hz 47Hz – 160Hz

Coverage Angle H90° x V60° Constant Directivity Horn –

Crossover Type FIR-X tuning

™ (Linear Phase FIR Filter) –

Crossover Frequency 2.1kHz 2.1kHz 2.3kHz 2.4kHz –

Measured Maximum SPL (peak)

IEC noise@1m

133dB SPL 132dB SPL 131dB SPL 129dB SPL 132dB SPL 131dB SPL

Transducer DXR15 DXR12 DXR10 DXR8 DXS15 DXS12

LF Diameter 15" Cone 12" Cone 10" Cone 8" Cone 15" Cone 12" Cone

Voice coil 2.5" 2.5" 2" 2" 2.5" 2.5"

Magnet Ferrite

HF Diaphragm 1.4" –

Type 1" Throat Compression Driver –

Magnet Ferrite –

Enclosure DXR15 DXR12 DXR10 DXR8 DXS15 DXS12

Material, Finish, Color ABS, Matte Black Wood, Paint, Black

Floor Monitor Angle 50° Symmetrical 50° Symmetrical 50° – –

Dimensions

(WxHxD, with rubber feet)

445×700×380 mm

(17-1/2" x 27-1/2"

x 15")

362×601×350 mm

(14-1/4" x 23-5/8"

x 13-3/4")

305×502×310 mm

(12" x 19-3/4"

x 12-1/4")

280×458×280 mm

(11" x 18" x 11")

478×618×624 mm

(18-7/8" x 24-3/8"

x 24-1/2")

397×563×594 mm

(15-5/8" x 22-1/8"

x 23-3/8")

Net Weight 22.5kg (49.6lbs) 19.3kg (42.5lbs) 14.6kg (32.2lbs) 13.5kg (29.8lbs) 38.0kg (83.8lbs) 33.0kg (72.8lbs)

Handles Aluminium die-cast (Side x 2) Aluminium die-cast (Top x 1) Metal (Side x 2)

Pole Socket 35mm with 2-way feature (0 or 7 degree) 35mm (Top)

Rigging points Top x 2, Rear x 1

(Fits for M10 x 18mm eyebolts)

Top x 2, Rear x 1

(Fits for M8 x 15mm eyebolts)

–

Optional Accessory (U-bracket) UB-DXR15 UB-DXR12 UB-DXR10 UB-DXR8 –

Amplifier DXR15 DXR12 DXR10 DXR8 DXS15 DXS12

Amplifier Type Class-D Class-D

Power Rating

Dynamic 1100W (LF: 950W, HF: 150W) 950W

Continuous 700W (LF: 600W, HF: 100W) 600W

Cooling Fan cooling, 4 speeds

AD/DA 24bit 48kHz sampling

Signal Processing 48bit (Accumulator: 76bit)

HPF/LPF OFF, 100, 120Hz 24dB/oct HPF 80, 100, 120Hz 24dB/oct LPF

DSP preset D-CONTOUR: FOH/MAIN, MONITOR, OFF D-XSUB: BOOST, XTENDED-LF, OFF

Protection Speaker Clip limiting, Integral Power Protection, DC-fault

Amplifier Thermal, Output over current

Power supply Thermal, Output over voltage, Output over current

Connectors Input INPUT1: XLR3-31 x 1, INPUT2: Phone x 2 (Unbalanced),

INPUT3: RCA PIN x 2 (Unbalanced)

INPUT: XLR3-31 x 2

Output THRU: XLR3-32 x 1 (Parallel with INPUT1), LINK OUT: XLR x1 THRU: XLR3-32 x 2 (Parallel with INPUT)

Input

Impedance

INPUT1 LINE: 12kΩ, MIC: 8kΩ 10kΩ

INPUT2, 3 L, R: 40kΩ, MONO: 20kΩ –

Input Sensitivity

(LEVEL:

Maximum)

INPUT1 LINE: +1dBu, MIC: -32dBu +1dBu

INPUT2, 3 -13dBu –

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 81

References

Italiano

Español

Français

Deutsch

English

0dBu is referenced to 0.775Vrms.

*1 Power rating (120V, 25°C). This is total value of individual output power.

Input Sensitivity

(LEVEL:

Center)

INPUT1 LINE: +11dBu, MIC: -22dBu +11dBu

INPUT2, 3 -3dBu –

Maximum Input

Level

INPUT1 LINE: +24dBu, MIC: +20dBu +24dBu

INPUT2, 3 +16dBu –

Controls LEVEL x3, LINE/MIC, HPF, D-CONTOUR, FRONT LED DISABLE, LINK MODE,

POWER

LEVEL, POLARITY, LPF, D-XSUB,

FRONT LED DISABLE, POWER

Idle Power Consumption 35W

1/8 Power Consumption 110W 90W 120W

Power Requirements 100V – 240V, 50Hz/60Hz

Amplifier DXR15 DXR12 DXR10 DXR8 DXS15 DXS12

82 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

References

Italiano

Español

Français

Deutsch

English

Dimensions

DXR8

280

458

DXR12

362 350

601

402

50°

DXR10

305 310

355

50°

502

DXR15

445 380

456

700

50°

Unit: mm Unit: mm

DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual 83

References

Italiano

Español

Français

Deutsch

English

DXS12DXS15

Unit: mm Unit: mm

478

618

624

397

563

594

84 DXR15/DXR12/DXR10/DXR8/DXS15/DXS12 Owner’s Manual

References

Italiano

Español

Français

Deutsch

English

Block Diagram

DXS block diagram

DXR block diagram

●PROTECTION●LIMIT

1 (MIC/LINE)

THRU

LINE/

MIC (100Hz HPF)

120Hz

LIMITER

SIGNAL

EQ FIR-X

DELAY LIMITER

AMP

(HF)

AMP

(LF)

MUTE

TEMP.

DC-FAULT

OUTPUT

CURRENT

OUTPUT

VOLTAGE

INTEGRAL

OUTPUT

POWER

ON/OFF

MUTE

PROTECTION LOGIC

MONITOR

D-CONTOUR

FOH/MAIN

OFF

HPF

100Hz

OFF

L/MONO

2 (LINE)

3 (LINE)

LINK OUT (LINE)

LEVEL

INPUT

DSP

MONO: INPUT1+2(L+R)+3(L+R)

STEREO: INPUT1+2(R)+3(R)

MONO: INPUT1+2(L+R)+3(L+R)

STEREO: INPUT1+2(L)+3(L)

INPUT MIX

LINK (MONO/STEREO)

120Hz

SIGNAL

DELAY

AMP

TEMP. DC-FAULT

OUTPUT

CURRENT

OUTPUT

VOLTAGE

INTEGRAL

OUTPUT

POWER

ON/OFF

MUTE

PROTECTION LOGIC

D-XSUBLPF

100Hz

80Hz

SUB WOOFER

AD DA

DSP

PORALITY

L (LINE)

THRU

LEVEL

INPUT

R (LINE)

THRU

INPUT MIX

XTENDED LF

BOOST

OFF

●PROTECTION

●LIMIT

LIMITER

MUTE

(weee_eu)

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should

not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with

your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on hu-

man health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal ser-

vice or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the

correct method of disposal.

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte

Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische

Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC, bringen Sie alte Geräte bitte zur fach-

gerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen und verhindern mögliche nega-

tive Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten

könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte, kontaktieren Sie bitte Ihre örtliche Stadt- oder Ge-

meindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

[Information für geschäftliche Anwender in der Europäischen Union]

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.

[Entsorgungsinformation für Länder außerhalb der Europäischen Union]

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Be-

hörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.

Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne

doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les

déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de

précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement

inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez

contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits.

[Pour les professionnels dans l'Union Européenne]

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour

plus d'informations.

[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]

Ce symbole est seulement valables dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et élec-

troniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée.

Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo

Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos

usados no deben ser mezclados con desechos hogareños corrientes.

Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplica-

bles, de acuerdo a su legislación nacional y las directivas 2002/96/EC.

Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo

sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.

Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de

gestión de residuos o el punto de venta en el cual usted adquirió los artículos.

[Para usuarios de negocios en la Unión Europea]

Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor información.

[Información sobre la Disposición en otros países fuera de la Unión Europea]

Este símbolo sólo es válidos en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte

por el método correcto de disposición.

Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura

Questo simbolo sui prodotti, sull’imballaggio, e/o sui documenti che li accompagnano significa che i prodotti elettriche e elettroniche

non dovrebbero essere mischiati con i rifiuti domestici generici.

Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con

la Sua legislazione nazionale e le direttive 2002/96/CE.

Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla sa-

lute umana e l'ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo

servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.

[Per utenti imprenditori dell'Unione europea]

Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni.

[Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea]

Questo simbolo è validi solamente nell'Unione europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il rivenditore

e richieda la corretta modalità di smaltimento.

Important Notice: Guarantee Information for customers in EEA* and Switzerland

English

Wichtiger Hinweis: Garantie-Information für Kunden in der EWR* und der Schweiz

Deutsch

Remarque importante: informations de garantie pour les clients de l’EEE et la Suisse

Français

Belangrijke mededeling: Garantie-informatie voor klanten in de EER* en Zwitserland

Nederlands

Aviso importante: información sobre la garantía para los clientes del EEE* y Suiza

Español

Avviso importante: informazioni sulla garanzia per i clienti residenti nell’EEA* e in Svizzera

Italiano

Aviso importante: informações sobre as garantias para clientes da AEE* e da Suíça

Português

Σημαντική σημείωση: Πληροφορίες εγγύησης για τους πελάτες στον ΕΟΧ* και Ελβετία

Ελληνικά

Viktigt: Garantiinformation för kunder i EES-området* och Schweiz

Svenska

Viktig merknad: Garantiinformasjon for kunder i EØS* og Sveits

Norsk

Vigtig oplysning: Garantioplysninger til kunder i EØO* og Schweiz

Dansk

Tärkeä ilmoitus: Takuutiedot Euroopan talousalueen (ETA)* ja Sveitsin asiakkaille

Suomi

Ważne: Warunki gwarancyjne obowiązujące w EOG* i Szwajcarii

Polski

Důležité oznámení: Záruční informace pro zákazníky v EHS* a ve Švýcarsku

Česky

Magyar

Oluline märkus: Garantiiteave Euroopa Majanduspiirkonna (EMP)* ja Šveitsi klientidele

Eesti keel

Svarīgs paziņojums: garantijas informācija klientiem EEZ* un Šveicē

Latviešu

Dėmesio: informacija dėl garantijos pirkėjams EEE* ir Šveicarijoje

Lietuvių kalba

Dôležité upozornenie: Informácie o záruke pre zákazníkov v EHP* a Švajčiarsku

Slovenčina

Pomembno obvestilo: Informacije o garanciji za kupce v EGP* in Švici

Slovenščina

Важно съобщение: Информация за гаранцията за клиенти в ЕИП* и Швейцария

Български език

За подробна информация за гаранцията за този продукт на Yamaha и гаранционното обслужване в паневропейската зона на

ЕИП* и Швейцария или посетете посочения по-долу уеб сайт (на нашия уеб сайт има файл за печат), или се свържете с

представителния офис на Yamaha във вашата страна (следваща страница). * ЕИП: Европейско икономическо пространство

Limba română

http://europe.yamaha.com/warranty/

URL_3

Important Notice: Guarantee Information

for customers in European Economic Area

(EEA) and Switzerland

For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either

visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your

country (next page). * EEA: European Economic Area

Für nähere Garantie-Information über dieses Produkt von Yamaha, sowie über den Pan-EWR*- und Schweizer Garantieservice, besuchen

Sie bitte entweder die folgend angegebene Internetadresse (eine druckfähige Version befindet sich auch auf unserer Webseite), oder

wenden Sie sich an den für Ihr Land zuständigen Yamaha-Vertrieb (nächste Seite). *EWR: Europäischer Wirtschaftsraum

Pour des informations plus détaillées sur la garantie de ce produit Yamaha et sur le service de garantie applicable dans l’ensemble

de l’EEE ainsi qu’en Suisse, consultez notre site Web à l’adresse ci-dessous (le fichier imprimable est disponible sur notre site

Web) ou contactez directement Yamaha dans votre pays de résidence (page suivante). * EEE : Espace Economique Européen

Voor gedetailleerde garantie-informatie over dit Yamaha-product en de garantieservice in heel de EER* en Zwitserland, gaat u

naar de onderstaande website (u vind een afdrukbaar bestand op onze website) of neemt u contact op met de vertegenwoordiging

van Yamaha in uw land (volgende pagina). * EER: Europese Economische Ruimte

Para una información detallada sobre este producto Yamaha y sobre el soporte de garantía en la zona EEE* y Suiza, visite la

dirección web que se incluye más abajo (la version del archivo para imprimir esta disponible en nuestro sitio web) o póngase en

contacto con el representante de Yamaha en su país (página siguiente). * EEE: Espacio Económico Europeo

Per informazioni dettagliate sulla garanzia relativa a questo prodotto Yamaha e l’assistenza in garanzia nei paesi EEA* e in

Svizzera, potete consultare il sito Web all’indirizzo riportato di seguito (è disponibile il file in formato stampabile) oppure contattare

l’ufficio di rappresentanza locale della Yamaha (pagina seguente). * EEA: Area Economica Europea

Para obter uma informação pormenorizada sobre este produto da Yamaha e sobre o serviço de garantia na AEE* e na Suíça,

visite o site a seguir (o arquivo para impressão está disponível no nosso site) ou entre em contato com o escritório de representa-

ção da Yamaha no seu país (próxima página). * AEE: Área Econômica Européia

Για λεπτομερείς πληροφορίες εγγύησης σχετικά με το παρόν προϊόν της Yamaha και την κάλυψη εγγύησης σε όλες τις χώρες του

ΕΟΧ και την Ελβετία, επισκεφτείτε την παρακάτω ιστοσελίδα (Εκτυπώσιμη μορφή είναι διαθέσιμη στην ιστοσελίδα μας) ή

απευθυνθείτε στην αντιπροσωπεία της Yamaha στη χώρα σας (επόμενη σελίδα). * ΕΟΧ: Ευρωπαϊκός Οικονομικός Χώρος

För detaljerad information om denna Yamahaprodukt samt garantiservice i hela EES-området* och Schweiz kan du antingen

besöka nedanstående webbaddress (en utskriftsvänlig fil finns på webbplatsen) eller kontakta Yamahas officiella representant i

ditt land (nästa sida). * EES: Europeiska Ekonomiska Samarbetsområdet

Detaljert garantiinformasjon om dette Yamaha-produktet og garantiservice for hele EØS-området* og Sveits kan fås enten ved å

besøke nettadressen nedenfor (utskriftsversjon finnes på våre nettsider) eller kontakte kontakte Yamaha-kontoret i landet der du

bor (neste side). *EØS: Det europeiske økonomiske samarbeidsområdet

De kan finde detaljerede garantioplysninger om dette Yamaha-produkt og den fælles garantiserviceordning for EØO* (og Schweiz)

ved at besøge det websted, der er angivet nedenfor (der findes en fil, som kan udskrives, på vores websted), eller ved at kontakte

Yamahas nationale repræsentationskontor i det land, hvor De bor (næste side). * EØO: Det Europæiske Økonomiske Område

Tämän Yamaha-tuotteen sekä ETA-alueen ja Sveitsin takuuta koskevat yksityiskohtaiset tiedot saatte alla olevasta nettiosoit-

teesta. (Tulostettava tiedosto saatavissa sivustollamme.) Voitte myös ottaa yhteyttä paikalliseen Yamaha-edustajaan (seuraavalla

sivulla). *ETA: Euroopan talousalue

Aby dowiedzieć się więcej na temat warunków gwarancyjnych tego produktu firmy Yamaha i serwisu gwarancyjnego w całym EOG* i

Szwajcarii, należy odwiedzić wskazaną poniżej stronę internetową (Plik gotowy do wydruku znajduje się na naszej stronie internetowej)

lub skontaktować się z przedstawicielstwem firmy Yamaha w swoim kraju (następna strona). * EOG — Europejski Obszar Gospodarczy

Podrobné záruční informace o tomto produktu Yamaha a záručním servisu v celém EHS* a ve Švýcarsku naleznete na níže

uvedené webové adrese (soubor k tisku je dostupný na našich webových stránkách) nebo se můžete obrátit na zastoupení firmy

Yamaha ve své zemi (další stránka). * EHS: Evropský hospodářský prostor

A jelen Yamaha termékre vonatkozó részletes garancia-információk, valamint az EGT*-re és Svájcra kiterjedő garanciális

szolgáltatás tekintetében keresse fel webhelyünket az alábbi címen (a webhelyen nyomtatható fájlt is talál), vagy pedig lépjen

kapcsolatba az országában működő Yamaha képviseleti irodával (következő oldal). * EGT: Európai Gazdasági Térség

Täpsema teabe saamiseks selle Yamaha toote garantii ning kogu Euroopa Majanduspiirkonna ja Šveitsi garantiiteeninduse kohta,

külastage palun veebisaiti alljärgneval aadressil (meie saidil on saadaval prinditav fail) või pöörduge Teie regiooni Yamaha

esinduse poole (järgmine lehekülg). * EMP: Euroopa Majanduspiirkond

Lai saņemtu detalizētu garantijas informāciju par šo Yamaha produktu, kā arī garantijas apkalpošanu EEZ* un Šveicē, lūdzu,

apmeklējiet zemāk norādīto tīmekļa vietnes adresi (tīmekļa vietnē ir pieejams drukājams fails) vai sazinieties ar jūsu valsti

apkalpojošo Yamaha pārstāvniecību (nākamā lappuse). * EEZ: Eiropas Ekonomikas zona

Jei reikia išsamios informacijos apie šį „Yamaha“ produktą ir jo techninę priežiūrą visoje EEE* ir Šveicarijoje, apsilankykite mūsų

svetainėje toliau nurodytu adresu (svetainėje yra spausdintinas failas) arba kreipkitės į „Yamaha“ atstovybę savo šaliai (kitas

puslapis). *EEE – Europos ekonominė erdvė

Podrobné informácie o záruke týkajúce sa tohto produktu od spoločnosti Yamaha a garančnom servise v EHP* a Švajčiarsku

nájdete na webovej stránke uvedenej nižšie (na našej webovej stránke je k dispozícii súbor na tlač) alebo sa obráťte na zástupcu

spoločnosti Yamaha vo svojej krajine (nasledujúca strana). * EHP: Európsky hospodársky priestor

Pentru informaţii detaliate privind acest produs Yamaha şi serviciul de garanţie Pan-SEE* şi Elveţia, vizitaţi site-ul la adresa de

mai jos (fişierul imprimabil este disponibil pe site-ul nostru) sau contactaţi biroul reprezentanţei Yamaha din ţara dumneavoastră

(pagina următoare). * SEE: Spaţiul Economic European

Za podrobnejše informacije o tem Yamahinem izdelku ter garancijskem servisu v celotnem EGP in Švici, obiščite

spletno mesto, ki je navedeno spodaj (natisljiva datoteka je na voljo na našem spletnem mestu), ali se obrnite na Yamahinega

predstavnika v svoji državi (naslednja stran). * EGP: Evropski gospodarski prostor

Fontos figyelmeztetés: Garancia-információk az EGT* területén és Svájcban élő vásárlók számára

Notificare importantă: Informaţii despre garanţie pentru clienţii din SEE* şi Elveţia

e_list_2

Yamaha Representative Offices in Europe

AUSTRIA

Yamaha Music Europe GmbH

Branch Austria

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

BELGIUM

Yamaha Music Europe

Branch Benelux

Clarissenhof 5b NL, 4133 AB. Vianen

The Netherlands

Tel: +31 (0)347 358040

Fax: +31 (0)347 358060

BULGARIA

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

CYPRUS

NAKAS Music Cyprus Ltd.

31C Nikis Ave., 1086 Nicosia

Tel: +357 (0)22 510 477

Fax: +357 (0)22 511 080

CZECH REPUBLIC

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

DENMARK

YS Copenhagen Liaison Office

(Yamaha Scandinavia AB Filial Denmark)

Generatorvej 6A, 2730 Herlev, Denmark

Tel: +45 44 92 49 00

Fax: +45 44 54 47 09

ESTONIA

Yamaha Music Europe GmbH

Sp. z o.o. Oddział w Polsce

(Branch Poland)

ul. 17 Stycznia 56

PL-02-146 Warszawa Poland

Tel: +48 (0)22 500 29 25

Fax: +48 (0)22 500 29 30

FINLAND

(For Musical Instrument)

F - Musiikki OY

Kaisaniemenkatu 7, PL260

00101 Helsinki, Finland

Tel: +358 (0)9 618511

Fax: +358 (0)9 61851385

(For Pro Audio)

Yamaha Scandinavia AB

J A Wettergrens gata 1

Västra Frölunda, Sweden

(Box 300 53, 400 43 Goteborg

Sweden - Postal Address)

Tel: +46 (0)31 893400

Fax: +46 (0)31 454026

FRANCE

Yamaha Musique France

Zone d’activité de Pariest

7, rue Ambroise Croizat

77183 Croissy-Beaubourg, France

(B.P. 70, 77312 Marne la Vallée Cedex 2

France-Adresse postale)

Tel: +33 (0)1 64 61 4000

Fax: +33 (0)1 64 61 4079

GERMANY

Yamaha Music Europe GmbH

Siemensstr 22-34

D-25462 Rellingen, b. Hamburg, Germany

Tel: +49 (0)4101 3030

Fax: +49 (0)4101 303 77702

GREECE

PH. Nakas S.A.Music House/Service

19 KM Leoforos Lavriou

19002 Peania / Attiki, Greece

Tel: +30 (0)210 6686260

Fax: +30 (0)210 6686269

HUNGARY

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

ICELAND

(For Musical Instrument)

HLJODFAERAHUSID EHF

Sidumula 20

108 Reykjavik, Iceland

Tel: +354 525 50 50

Fax: +354 568 65 14

(For Pro Audio)

Yamaha Scandinavia AB

J A Wettergrens gata 1

Västra Frölunda, Sweden

(Box 300 53, 400 43 Goteborg

Sweden - Postal Address)

Tel: +46 (0)31 893400

Fax: +46 (0)31 454026

IRELAND (REPUBLIC OF IRELAND)

Yamaha Music UK Ltd.

Sherbourne Drive

Tilbrook, Milton Keynes MK7 8BL

United Kingdom

Tel: +353 (0) 1526 2449

Fax: +44 (0) 1908 369278

ITALY

Yamaha Musica Italia s.p.a.

Viale Italia 88

20020, Lainate (Milano), Italy

Tel: +39 (0)02 93577 1

Fax: +39 (0)02 937 0956

LATVIA

Yamaha Music Europe GmbH

Sp. z o.o. Oddział w Polsce

(Branch Poland)

ul. 17 Stycznia 56

PL-02-146 Warszawa Poland

Tel: +48 (0)22 500 29 25

Fax: +48 (0)22 500 29 30

LIECHTENSTEIN

Yamaha Music Europe GmbH, Rellingen,

Branch Switzerland in Zurich

Seefeldstrasse 94, CH-8008

Zürich, Switzerland

Tel: +41 (0)44 3878080

Fax: +41 (0)44 3833918

LITHUANIA

Yamaha Music Europe GmbH

Sp. z o.o. Oddział w Polsce

(Branch Poland)

ul. 17 Stycznia 56

PL-02-146 Warszawa Poland

Tel: +48 (0)22 500 29 25

Fax: +48 (0)22 500 29 30

LUXEMBOURG

Yamaha Music Europe

Branch Benelux

Clarissenhof 5b NL, 4133 AB. Vianen

The Netherlands

Tel: +31 (0)347 358040

Fax: +31 (0)347 358060

MALTA

Olimpus Music Ltd.

The Emporium, Level 3, St. Louis Street

Msida MSD06

Tel: +356 (0)2133 2093

Fax: +356 (0)2133 2144

NETHERLANDS

Yamaha Music Europe

Branch Benelux

Clarissenhof 5b NL, 4133 AB. Vianen

The Netherlands

Tel: +31 (0)347 358040

Fax: +31 (0)347 358060

NORWAY

YS Oslo Liaison Office

(Yamaha Scandinavia AB Filial Norway)

Grini Naeringspark 1

1361 Osteras, Norway

Tel: +47 67 16 77 70

Fax: +47 67 16 77 79

POLAND

YAMAHA Music Europe GmbH

Sp. z o.o. Oddział w Polsce

ul. 17 Stycznia 56

02-146 WARSZAWA/POLSKA

Tel: +48 (0)22 500 29 25

Fax: +48 (0)22 500 29 30

PORTUGAL

Yamaha Música Ibérica, S.A.U.

Sucursal Portuguesa

Rua Alfredo da Silva

2610-016 Amadora, Portugal

Tel: +351 214 704 330

Fax: +351 214 718 220

ROMANIA

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

SLOVAKIA

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

SLOVENIA

Yamaha Music Europe GmbH

Branch Austria (Central and Eastern Europe)

Schleiergasse 20, A-1100 Wien Austria

Tel: +43 (0)1 602 03900

Fax: +43 (0)1 602 039051

SPAIN

Yamaha Música Ibérica, S.A.U.

Ctra. de la Coruna km.17, 200

28230 Las Rozas de Madrid, Spain

Tel: +34 902 39 8888

Fax: +34 91 638 4660

SWEDEN

Yamaha Scandinavia AB

J A Wettergrens gata 1

Västra Frölunda, Sweden

(Box 300 53, 400 43 Goteborg

Sweden - Postal Address)

Tel: +46 (0)31 893400

Fax: +46 (0)31 454026

SWITZERLAND

Yamaha Music Europe GmbH, Rellingen,

Branch Switzerland in Zurich

Seefeldstrasse 94, CH-8008

Zürich, Switzerland

Tel: +41 (0)44 3878080

Fax: +41 (0)44 3833918

UNITED KINGDOM

Yamaha Music UK Ltd.

Sherbourne Drive

Tilbrook, Milton Keynes MK7 8BL

United Kingdom

Tel: +44 (0) 870 4445575

Fax: +44 (0) 1908 369278

Strona jest ładowana ...

Yamaha DXR15 Instrukcja obsługi

Marka: Yamaha

Model: DXR15

Kategoria: Wzmacniacz instrumentów muzycznych

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

čeština: Yamaha DXR15 Návod k obsluze
español: Yamaha DXR15 El manual del propietario
italiano: Yamaha DXR15 Manuale del proprietario
Deutsch: Yamaha DXR15 Bedienungsanleitung
svenska: Yamaha DXR15 Bruksanvisning
português: Yamaha DXR15 Manual do proprietário
français: Yamaha DXR15 Le manuel du propriétaire
Türkçe: Yamaha DXR15 El kitabı
English: Yamaha DXR15 Owner's manual
dansk: Yamaha DXR15 Brugervejledning
русский: Yamaha DXR15 Инструкция по применению
suomi: Yamaha DXR15 Omistajan opas
Nederlands: Yamaha DXR15 de handleiding
română: Yamaha DXR15 Manualul proprietarului

Yamaha DXR15 Instrukcja obsługi

Yamaha DXR15 Instrukcja obsługi

w innych językach

Powiązane dokumenty